Go Back   Two Wheel Fix > In the Garage or Shop > Mechanical or Tech

Reply
 
Thread Tools Display Modes
Old 01-17-2009, 05:53 PM   #1
Phenix_Rider
WERA White Plate
 
Phenix_Rider's Avatar
 
Join Date: Feb 2008
Location: Renton, WA
Moto: Ninja 650R
Posts: 1,920
Default Changinf chain and sprockets

I've tried a 1/2" breaker bar, mallet on the breaker bar, and a 1/2" air impact gun. Cannot get my front sprocket nut loose. I have someone holding the rear brake with it in neutral, so the rear wheel isn't moving. I made sure the washer is clear of the nut, sprayed it with WD40... I marked the nut with a permanent marker, and the SOB won't turn! With the breaker bar, I figured the suspension was compressing. With the impact, I can see the chain shaking. This thing is supposed to be torqued to 92 ft-lbs. The impact gun should have several hundred ft-lbs. I just tried again with a 3' length of pipe on the handle of my breaker bar, using a 6-point socket, with someone on the rear brake and the bike in first. That's a couple hundred ft-lbs at least. I turned the rear wheel, and turned the engine over! What is wrong here? Everything I've found, and my inspection of the threads says this nut is standard- left should be loose!! (counterclockwise)

What kind of king kong maniac with an impact wrench put this thing on?
__________________
Quote:
So you think you're ready to ride? So if i ran up to you with a belt sander would you feel safe????
Phenix_Rider is offline   Reply With Quote
Old 01-17-2009, 06:19 PM   #2
Cutty72
Ride Naked.
 
Cutty72's Avatar
 
Join Date: Feb 2008
Location: Flat and Straight ND
Moto: 08 BUELL 1125R, 05 SV650S
Posts: 7,916
Default

My guess would be it's a left handed thread, just cause of the normal direction of rotation.

is there a locking ring or key in it?

That's the ideas I have, sorry.
__________________
Adrenaline... the wonder drug.

Quote:
Originally Posted by Gas Man View Post
Again... Cutty you are one smart man!!
Quote:
Originally Posted by The Chi View Post
If I have to get help to get it back up, I dont need to be riding it.

3662 Supply NCO

Cutty72 is offline   Reply With Quote
Old 01-18-2009, 04:59 AM   #3
Gas Man
Trip's Assistant
 
Gas Man's Avatar
 
Join Date: Feb 2008
Location: Imported from Detroit
Moto: 2009 HD Street Classic
Posts: 12,149
Default

Cutty is right... could be either.

Also try a higher gear in the tranny... higher gear=bigger gear.

Also consider that nut was probably put on with high strength loctite. Get a heat gun and heat it up then hit it with the impact gun. Make sure your air compressor is turned up!
__________________
-Chris



"Why pay somebody else to fuck up your bike?"
Run Amsoil Product
Gas Man is offline   Reply With Quote
Old 01-18-2009, 11:34 AM   #4
mlkx3
6.72 1/8 mile
 
mlkx3's Avatar
 
Join Date: Feb 2008
Location: Iowa
Moto: 06 ZX10R
Posts: 8
Default

If its anyting like the 10r, use a slightly bigger socket to pound the washer away from the nut. Inspect and use a punch and hammer to do the same, it looks like its flat enough but its not, its a kawi thing.
mlkx3 is offline   Reply With Quote
Old 01-18-2009, 03:41 PM   #5
Phenix_Rider
WERA White Plate
 
Phenix_Rider's Avatar
 
Join Date: Feb 2008
Location: Renton, WA
Moto: Ninja 650R
Posts: 1,920
Default

Finally got the motherfucker loose. Had to go out and buy a 625 ft-lb impact, beat the snot out of the washer, and use a heat gun. After all that, it still took reversing the impact several times, then when it finally broke loose, the nut came flying off and skittered across the floor. The sprocket itself came off the shaft with two fingers.

Whatever prick put the thing on didn't know how to use a torque wrench. That was no 92 ft-lbs.
__________________
Quote:
So you think you're ready to ride? So if i ran up to you with a belt sander would you feel safe????

Last edited by Phenix_Rider; 01-18-2009 at 03:44 PM..
Phenix_Rider is offline   Reply With Quote
Old 01-18-2009, 06:55 PM   #6
Phenix_Rider
WERA White Plate
 
Phenix_Rider's Avatar
 
Join Date: Feb 2008
Location: Renton, WA
Moto: Ninja 650R
Posts: 1,920
Default

Damnit. Apparently all 520 chains are not alike. The stock rivet master link I got at the dealer doesn't fit the new RK chain. So I had to put the stupid clip master in that the chain came with. Now I have to order an RK rivet master. Other than that, no (more) problems to report. it's ridable.
__________________
Quote:
So you think you're ready to ride? So if i ran up to you with a belt sander would you feel safe????
Phenix_Rider is offline   Reply With Quote
Old 01-18-2009, 11:31 PM   #7
bmblebee
Community Curmudgeon
 
bmblebee's Avatar
 
Join Date: Nov 2008
Location: Tallahassee
Moto: '04 F4i
Posts: 373
Default

Don't forget to safety wire the clip master link, I have had them come apart. How did you compress the plate on the link before you installed the clip?
__________________
Alcohol, Tobacco and Firearms should be a convenience store and not a government agency

If You Don't Know What Your Rights are...You Won't Have Any
bmblebee is offline   Reply With Quote
Old 01-18-2009, 11:49 PM   #8
Gas Man
Trip's Assistant
 
Gas Man's Avatar
 
Join Date: Feb 2008
Location: Imported from Detroit
Moto: 2009 HD Street Classic
Posts: 12,149
Default

Yeah and I suggest you order 2 replacement links.. just in case you screw up the first one. Plus if you don't, you'll have a spare anyway.
__________________
-Chris



"Why pay somebody else to fuck up your bike?"
Run Amsoil Product
Gas Man is offline   Reply With Quote
Old 01-19-2009, 08:56 AM   #9
Phenix_Rider
WERA White Plate
 
Phenix_Rider's Avatar
 
Join Date: Feb 2008
Location: Renton, WA
Moto: Ninja 650R
Posts: 1,920
Default

Quote:
Originally Posted by bmblebee View Post
Don't forget to safety wire the clip master link, I have had them come apart. How did you compress the plate on the link before you installed the clip?
I won't be using the clip link AT ALL. I've heard way too much to trust it. I've only found the rivet master at chaparral, and it looks like I'm going to get ripped on shipping for a $6 part.
__________________
Quote:
So you think you're ready to ride? So if i ran up to you with a belt sander would you feel safe????
Phenix_Rider is offline   Reply With Quote
Old 01-19-2009, 06:50 PM   #10
bmblebee
Community Curmudgeon
 
bmblebee's Avatar
 
Join Date: Nov 2008
Location: Tallahassee
Moto: '04 F4i
Posts: 373
Default

buy several, you will use them
__________________
Alcohol, Tobacco and Firearms should be a convenience store and not a government agency

If You Don't Know What Your Rights are...You Won't Have Any
bmblebee is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:41 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.