Fast blinking blinkers.

Triple · 10-05-2009, 11:13 AM

...

Mikey · 10-05-2009, 11:17 AM

You usually see this when someone swaps out their stockers for LEDs. The LEDs have a much lower resistance rating than the standard bulbs, which is what causes the fast blinking. Figure out what the difference in resistance is and wire in a resistor inline and they will blink at the correct speed.

fasternyou929 · 10-05-2009, 11:19 AM

Quote:

Originally Posted by Triple

What causes this and how do you fix it?

Incorrect load on the "blinker" relay. You can usually add a resistor to the positive lead running to your turn signal to correct it. Did you recently change to LED turn signals or something else after market? Google turn signal and resistor and I'm sure you'll get some good values to start with. Resistors can be bought for a few cents at Radio Shack.

ETA: Dammit, Mikey apparently types much faster than me.

pauldun170 · 10-05-2009, 11:19 AM

In the car, it usually means a bulb is out.

Rider · 10-05-2009, 11:19 AM

LED blinkers have less resistance than the regular bulbs. You need to add a 5 ohm 100w resister in series for each blinker to slow down the blinking rate.

z06boy · 10-05-2009, 11:23 AM

I have fast blinking blinkers due to switching the stockers for aftermarket ones. I've gotten used to it and I'm fine with it.

I know the kit came with some resisters that would reduce the flow to slow the signals down BUT they get really hot and I didn't want the additional heat since the bike is so hot anyways plus with all of the plastic on the bike.

fasternyou929 · 10-05-2009, 11:33 AM

Quote:

Originally Posted by Rider

LED blinkers have less resistance than the regular bulbs. You need to add a 5 ohm 100w resister in series for each blinker to slow down the blinking rate.

100W? That's way overkill. I'm sure even a 25W would be plenty.

Mounting the resistor where some air will pass over it will help with any heat issues, but like z06 pointed out, I'd keep it away from plastics.

Rider · 10-05-2009, 11:36 AM

Quote:

Originally Posted by fasternyou929

100W? That's way overkill. I'm sure even a 25W would be plenty.

Mounting the resistor where some air will pass over it will help with any heat issues, but like z06 pointed out, I'd keep it away from plastics.

That's what came with my Clear Alternatives integrated tail light. It worked fine for me. It was a little warm but I zip tied them to part of the frame to keep them off the plastic.

fasternyou929 · 10-05-2009, 12:40 PM

Quote:

Originally Posted by Triple

That's what I thought and this was initially the case with my bike. The front-left blinker bulb was out, causing the rear-left blinker to flash at double speed. However, I replaced the front bulb and now they both flash at double speed.

I have aftermarket blinkers front and back, but I've had them on there for almost two years and the fast blinking didn't start until a bulb went out last week.

Then the bulb you used as a replacement doesn't have the same resistance as your stock ones. Same solutions apply.

karl_1052 · 10-05-2009, 01:48 PM

It could also be a bad flasher relay.

10-05-2009, 11:13 AM	#1
Triple uncomfortably numb Join Date: Nov 2008 Location: JOH-JAH! Moto: WR250R & Bonneville Posts: 409	Fast blinking blinkers. ... Last edited by Triple; 10-22-2009 at 03:19 PM..

10-05-2009, 11:17 AM	#2
Mikey Raving Lunatic Join Date: Nov 2008 Location: San Antonio, Texas Moto: Concours 14 ABS, ZX6E Posts: 902	You usually see this when someone swaps out their stockers for LEDs. The LEDs have a much lower resistance rating than the standard bulbs, which is what causes the fast blinking. Figure out what the difference in resistance is and wire in a resistor inline and they will blink at the correct speed. __________________ Slow is smooth, smooth is fast.

10-05-2009, 01:48 PM	#10
karl_1052 sergeant hatred Join Date: Jul 2009 Location: Ottawa Moto: The bus Posts: 2,723	It could also be a bad flasher relay. __________________ My wife was afraid of the dark...then she saw me naked and now she's afraid of the light.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

10-05-2009, 11:19 AM	#5
Rider Moto GP Star Join Date: Feb 2008 Posts: 12,156	LED blinkers have less resistance than the regular bulbs. You need to add a 5 ohm 100w resister in series for each blinker to slow down the blinking rate.

10-05-2009, 11:23 AM	#6
z06boy Letzroll Join Date: Feb 2008 Location: Lake Norman area, NC Moto: 07 Red R1 & 07 Blue R6 Posts: 5,265	I have fast blinking blinkers due to switching the stockers for aftermarket ones. I've gotten used to it and I'm fine with it. I know the kit came with some resisters that would reduce the flow to slow the signals down BUT they get really hot and I didn't want the additional heat since the bike is so hot anyways plus with all of the plastic on the bike.