WTF? how did THIS happen? - Page 2

Thumper996 · 02-03-2010, 09:49 PM

Hey, pick up a Wiseco bottom end kit, it comes with crank, rod, bearings, seals, gaskets, rod bearing and several other things for way better price than you can buy OEM stuff or individual.

www.wiseco.com

BobTheBiker · 02-04-2010, 03:18 AM

Quote:

Originally Posted by Thumper996

Hey, pick up a Wiseco bottom end kit, it comes with crank, rod, bearings, seals, gaskets, rod bearing and several other things for way better price than you can buy OEM stuff or individual.

www.wiseco.com

Will do. my bottom end is a bit rough anyhow, so Im just refreshing as many bearings as I can get to. I see ZERO reason to halfass it and do things wrong when I'll have money soon. right?

the most fun toy is the one you're NOT always tearing apart to fix instead of ride.

Rider · 02-04-2010, 08:57 AM

Quote:

Originally Posted by BobTheBiker

Will do. my bottom end is a bit rough anyhow, so Im just refreshing as many bearings as I can get to. I see ZERO reason to halfass it and do things wrong when I'll have money soon. right?

the most fun toy is the one you're NOT always tearing apart to fix instead of ride.

Go ahead and get a Wiseco top end while your at it. 25 hours is the recommended replacement interval for the top end in 2 stroke dirt bikes.

BobTheBiker · 02-04-2010, 09:15 AM

at a minimum I'm also putting a new piston in, since the old one was destroyed by some kid trying to get the wrist pin out or something, it looks like holy hell.

Rider · 02-04-2010, 09:19 AM

Quote:

Originally Posted by BobTheBiker

at a minimum I'm also putting a new piston in, since the old one was destroyed by some kid trying to get the wrist pin out or something, it looks like holy hell.

Watch those cir clips. Cover the case with a rag before you remove or install the cir clips. If one goes down into the crank case you are fucked. You'll need to split the case apart again. If you leave it there it will destroy your cylinder jug and piston. Ask me how I know.

askmrjesus · 02-04-2010, 09:36 AM

Quote:

Originally Posted by Rider

Ask me how I know.

Cause you're a klutz?

J/K I've done it too. Usually I can fish them out with a pencil magnet.

JC

BobTheBiker · 02-04-2010, 09:37 AM

I know that one. my friend had a circlip come out on his dad's RD400, and DESTROY a cylinder wall. needless to say, I'll be paying close attention to that detail.

since its a 2 stroke, theres no real limit to the HELL that can cause if one of those came out.

Rider · 02-04-2010, 09:42 AM

Quote:

Originally Posted by askmrjesus

Cause you're a klutz?

J/K I've done it too. Usually I can fish them out with a pencil magnet.

JC

Yeah I tried that and since I couldn't ever get the circlip out I assumed it just flew across the garage and didn't land in the crank case.. I was wrong.

askmrjesus · 02-04-2010, 09:57 AM

Quote:

Originally Posted by Rider

Yeah I tried that and since I couldn't ever get the circlip out I assumed it just flew across the garage and didn't land in the crank case.. I was wrong.

Ow....

They should paint those fuckers international orange, and attach homing beacons to them.

JC

BobTheBiker · 02-04-2010, 10:06 AM

yeah, they should. those little bastards are gifts from satan. I'm almost tempted to find out if snap rings would be an appropriate replacement for them.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

02-03-2010, 09:49 PM	#11
Thumper996 VTwins and One Lungs rule Join Date: Jan 2010 Location: TN Moto: Turning wrenches on my rides Posts: 37	Hey, pick up a Wiseco bottom end kit, it comes with crank, rod, bearings, seals, gaskets, rod bearing and several other things for way better price than you can buy OEM stuff or individual. www.wiseco.com

02-04-2010, 09:15 AM	#14
BobTheBiker too much time on my hands Join Date: Jul 2008 Location: the northern district of god damn Moto: 01 ZX6R, looking for more now. Posts: 1,802	at a minimum I'm also putting a new piston in, since the old one was destroyed by some kid trying to get the wrist pin out or something, it looks like holy hell.

02-04-2010, 09:37 AM	#17
BobTheBiker too much time on my hands Join Date: Jul 2008 Location: the northern district of god damn Moto: 01 ZX6R, looking for more now. Posts: 1,802	I know that one. my friend had a circlip come out on his dad's RD400, and DESTROY a cylinder wall. needless to say, I'll be paying close attention to that detail. since its a 2 stroke, theres no real limit to the HELL that can cause if one of those came out.

02-04-2010, 10:06 AM	#20
BobTheBiker too much time on my hands Join Date: Jul 2008 Location: the northern district of god damn Moto: 01 ZX6R, looking for more now. Posts: 1,802	yeah, they should. those little bastards are gifts from satan. I'm almost tempted to find out if snap rings would be an appropriate replacement for them.